Are you tired of washing your car only to have it dotted with water spots which can only be removed through polishing? At EV Accessories we have the perfect solution that leaves a shiny, spot-free finish to your car every time with little effort. Our Pure Water Di Pressure Vessel water filter is the answer. Part of a perfect car cleaning solution, the Di Vessel filtration system removes dissolved particulates from the water leaving the water free from contaminates, meaning you can leave your car to dry naturally
Approved by ceramic coating specialist PP Protect, this pure water car wash filter is the perfect solution of achieving a spot free, smear free finish.
The Di pressure vessel has a capacity of 11 litre, and used in conjunction with included Di resin can produce top quality water which is suitable for any pure water application, including pole window cleaning, aquatics, drinking water, car valeting, gardening and hydroponics as well as fish keeping.
Clunk click hose fittings are included and this resin vessel is supplied full of MB-115 for normal water or MB-151 Di Resin for hard water areas by selecting the checkbox above.
This is a CE approved, brand new resin vessel; it has not been recycled or reclaimed. Our low prices are because we source direct from a UK based distributor, not a re seller. This product is guaranteed to provide quality service to you, and if you look after this vessel, it can last you a life time. (we supply these direct from the supplier).
DI Pressure Vessel Water Filter Features:
- 11 litre capacity Di Pressure Vessel.
- Includes stand (built in base)
- Clunk click hose fittings included. (Hose Connectors are required)
- Complete Di vessel, all parts included and assembled, (riser pipe, resin head, and internal parts).
- Complies with all requirements of P.E.D. 97/23/EC directive.
- Suitable for drinking water following KTW recommendations.
- DI Vessel may come in Black or Blue depending on stock
Di Pressure Vessel Operating Specifications:
- Maximum pressure: 10.5 bar (150 psi)
- Maximum temperature: 49 °C (120 °F)
- Minimum temperature 1 °C (34 °F)
- Maximum vacuum: 127 mm Hg (5″ Hg)
- Vessel approved for water filtration use only
- Vessel must not be exposed to temperature below -29 °C (-20 °F)
Simply wash your car as normal and then plug in one of our pure water car wash filters into your hose and rinse down the car with pure water!
There’s no need to dry after if you don’t want to. This is because the filter will remove all the minerals or impurities leaving just water on the vehicle! (always rinse 100% of the car shampoo off for best results).
DO NOT use your water filter with a pressure washer. It will deplete the resin within 60 mins of use time. Use on a standard cold tap feed at normal pressure, use a length of new clean hose from the water filter “out” and keep that run of hose just for the filtered water.
You can test the water with a TDS meter also available from our shop. We supplier the filter in two versions to best suite your water area. EV Accessories pure water car wash water filters are approved by PP Protect vehicle ceramic coating specialists.
Pure Water Di Pressure Vessel Water Filter Care Instructions.
If stored in a cold place be sure to drain and empty the pressure vessel to prevent frost damage. The resin will remain wet for some time after use. We recommend that you drain excess was off if storing without use for more than one month. Do not shake and always store upright to avoid disturbing the resin bed.
You will need two Hozelock type Hose End Connectors and a ideally a brand new length of hose for the “out” side of the filter. They can also be purchased via our shop.
[amazon_link asins=’B000TAUEMA,B001OXFHVY,B002Q0EN96,B001OXDE0K,B0011NO7JK,B06VWTF2YD,B000TAP5WY,B0011NP992,B004EK1YXE,B001ULCILW’ template=’ProductCarousel’ store=’evac-21′ marketplace=’UK’ link_id=’b24cd476-65d8-46dc-82e3-e48855304196′].